1970 Plymouth Barracuda For Sale
1970 Plymouth Barracuda
Click HERE for more information about this vehicle.
1970 Barracuda! I have been collecting parts for many years and prefer to clean them out. I have installed a new quarter skin on the passenger side along with the outer fender and trunk extension. Need to install the inner trunk extension that I do not have as It is minitubbed and I was going to use a tub. You can finish it however you want. The corner of the skin didn\'t cover a small section which could be fabricated but I bought full quarters. So you are getting two skins 1 installed one not. You are getting 2 new goodmark full quarters, 2 trunk extensions and 2 outer fenders. I also have 2 new AMD front fenders that you will be getting also. The inner fenders on the front of the car have been replaced with goodmark repops. There are a ton of extra parts that I robbed from a 73 Cuda parts car as the doors and inner quarter panels (where the rear window cranks go) have been removed for lightening as it was a race car when I purchased it. I have The lightened doors and 2 original doors that are decent to replace and also have the material to fix the inner quarter panel area with all hardware for roll up windows as these do not roll up on the back. I was going to repair the original doors as they are lighter with the door bars removed you can do what you want. All of the floors and trunk are solid but this was a drag car and there are holes for whatever reason including where the roll cage was welded in. I would drive it like it is as it is solid you can do what you want. The suspension on the back is old school spring relocation coming off of the original hangers with 1/2 inch steel and a brace welded in for the rear mounts. All original frame rails are intact and solid I would properly minitubb it or run it like it is if you prefer as it is solid . The rearend is a 8 3/4 A body with a 4.88 spool and stock axles Which is why it looks better with the better offset wheels.. Wheels are Convo Pros 4\" on front and 10\" on back. Has aluminum radiator from summit racing. The engine is a 440 that was tore down to be freshened. The block is fresh from the machine shop it does have 1 sleeve where it was drilled through a freeze plug. Pistons are TRW pop up pistons with a set of Muscle Motors killer street heads that flow around 250 and have 2.14 and 1.81 valves. They have approximately 5000 miles on them. The pistons are in excellent condition with all of the knurl still on the side of the pistons with a fresh magged 413/440 crankshaft.the combo will be 12.5 to 1ish with popup and 10.5 to 1 with it milled of before you have it balanced. Have 2 sets of rods 1 stock set of ly rods and a set that was balanced and set up for full floaters. Also have steel roller rockers and holley intake manifold comp chain. Need to have assembly balanced and you buy rings and bearings. I do not have a cam.The trans is 727 with transbrake and 4000 converter for the transmission. I have 2 package trays for this car as it was modified and aluminum installed. I have just about everything you need to finish this car I just don\'t want to do it. Also have seats without foam and tracks but brand new set of black seat covers from PUI. Have aftermarket grill from Columbia parts and have an original that is broke. Have a fiberglass front bumper have brackets but not sure they are correct may be for a challenger. Rear bumper and brackets are intact and painted black.. It has 3 hoods one lightened factory 1 Non crumple zone original 70 hood and a hemi style fiberglass hood never been installed. I do not have hood hinges but have trunk hinges to be installed. The trunk on the car is lightened and the one original is a very nice trunk lid. I have a ton more photos but 24 is it for ebay. It has all the glass front windshield is new and the rest is original. Have extra back glass and1 extra side rear window. Have original rotors and calipers for a disk brake conversion on the front. I drove this car on the street until 2007 pulled the motor to make it faster and never made it back together as I had other projects to work on.It is wired for prostreet all lights and turn signals worked with toggle switches. Add brakes and engine and drive it like it is.
On Sep-18-18 at 20:11:49 PDT, seller added the following information:
On Sep-18-18 at 20:14:31 PDT, seller added the following information:
I have vin tag in my possession and it matches the radiator support and the cal area numbers.
On Sep-19-18 at 07:20:39 PDT, seller added the following information:
On Sep-20-18 at 12:02:23 PDT, seller added the following information:
This car was an original 318 3 or 4 speed. It has the small brake pedal and the clutch pedal is removed but could be put back on if you have one.
On Sep-22-18 at 04:47:21 PDT, seller added the following information:
If you want better quality pictures send me a question and I will try and get them to you as I can\'t change them after someone bids!
